こちらの商品は通電のみ確認致しました。
その為、現状でのお渡しとなります。
ノークレームノーリターンでお願い致します。
写真は代表の写真となります。
BootROM - 1.78
Booting from SPI flash, Secure mode
BootROM: RSA Public key verification PASSED
BootROM: CSK block signature verification PASSED
BootROM: Boot header signature verification PASSED
BootROM: Box ID verification PASSED
BootROM: JTAG is disabled
General initialization - Version: 1.0.0
Detected Device ID 6920
Master bootloder version 1.28
High speed PHY - Version: 2.0
BoardId = 0x21board SerDes lanes topology details:
| Lane # | Speed| Type |
------------------------------|
| 1 | 0 | SGMII1 |
| 2 | 5 | PCIe1 |
| 4 | 5 | PCIe2 |
| 5 | 0 | SGMII2 |
-------------------------------
:** Link is Gen1, check the EP capability
PCIe, Idx 1: Link upgraded to Gen2 based on client cpabilities
:** Link is Gen1, check the EP capability
PCIe, Idx 2: Link upgraded to Gen2 based on client cpabilities
High speed PHY - Ended Successfully
DDR4 Training Sequence - Ver TIP-0.23.(Sublib 0.8)0
DDR4 Training Sequence - Switching XBAR Window to FastPath Window
DDR4 Training Sequence - Ended Successfully
BootROM: Image checksum verification PASSED
BootROM: Boot image signature verification PASSED
____ _
/ ___|(_) ___ ___ ___
| | | |/ __| / __|/ _ \
| |___ | |\__ \| (__| (_) |
\____||_||___/ \___|\___/
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|
** LOADER **
U-Boot 2013.01-gba18bdb27 (Dec 21 2018 - 11:02:01) SDK version: 2015_T2.0p10
Board: Barbados-2K
SoC: MV88F6920 Rev A1
running 2 CPUs
CPU: ARM Cortex A9 MPCore (Rev 1) LE
CPU 0
CPU @ 1800 [MHz]
L2 @ 900 [MHz]
TClock @ 250 [MHz]
DDR4 @ 900 [MHz]
DDR4 32 Bit Width,FastPath Memory Access, DLB Enabled, ECC Disabled
DRAM: 1 GiB
RST I2C0
NAND: 256 MiB
SF: Detected MX25L3205D with page size 64 KiB, total 4 MiB
PCI-e 1 (IF 0 - bus 0) Root Complex Interface, Detected Link X1, GEN 2.0
PCI-e 2 (IF 1 - bus 1) Root Complex Interface, Detected Link X1, GEN 2.0
Map: Code: 0x3feda000:0x3ffae138
BSS: 0x3ffefc00
Stack: 0x3f9c9f20
Heap: 0x3f9ca000:0x3feda000
U-Boot Environment: 0x00100000:0x00110000 (SPI)
Board configuration:
| port | Interface | PHY address |
|--------|------------|--------------|
| egiga1 | SGMII | 0x01 |
| egiga2 | SGMII | 0x00 |
Net: , egiga1, egiga2 [PRIME]
Hit ESC key to stop autoboot: 0
Creating 1 MTD partitions on "nand0":
0x000000200000-0x000010000000 : "mtd=2"
UBI: attaching mtd1 to ubi0
UBIFS: mounted UBI device 0, volume 0, name "part1"
Loading file 'part1/part.bin' to addr 0x02000000 with size 46264093 (0x02c1ef1d)...
Done
SF: Detected MX25L3205D with page size 64 KiB, total 4 MiB
Checking image signing.
Image signing verification success, continue to run...
## Booting kernel from Legacy Image at 02000000 ...
Image Name: Barbados Firmware Image
Created: 2019-06-28 11:20:54 UTC
Image Type: ARM Linux Multi-File Image (uncompressed)
Data Size: 46263085 Bytes = 44.1 MiB
Load Address: 00008000
Entry Point: 00008000
Contents:
Image 0: 4105344 Bytes = 3.9 MiB
Image 1: 42141736 Bytes = 40.2 MiB
Image 2: 15989 Bytes = 15.6 KiB
Verifying Checksum ... OK
## Loading init Ramdisk from multi component Legacy Image at 02000000 ...
## Flattened Device Tree from multi component Image at 02000000
Booting using the fdt at 0x04c1acf8
Loading Multi-File Image ... OK
OK
reserving fdt memory region: addr=0 size=4000
Loading Device Tree to 01ff9000, end 01fffe74 ... OK
Starting Device Tree update ('fdt_skip_update' = no)
Limit DDR size at 3GB due to power of 2 requirement of Address decoding
Updating device tree successful
Starting kernel ...
[01/01/1970 00:00:00.0000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 260096
[01/01/1970 00:00:00.0000] Memory: 986960K/1048576K available (5588K kernel code, 399K rwdata, 2444K rodata, 355K init, 466K bss, 61616K reserved)
[01/01/1970 00:00:00.1200] CPU1: Booted secondary processor
[01/01/1970 00:00:10.4300] buginf tty flushing thread started, ttyport=be8b5000
[01/01/1970 00:00:10.5500] m25p80 spi1.0: found mx25l3206, expected n25q032
[*08/01/2034 00:14:49.5008] buginf() enabled.
[*08/01/2034 00:14:49.5097] Made it into bootsh: Jun 28 2019 04:12:29
[*08/01/2034 00:14:49.5098] bootsh build T-20ccf81671bf2dba46fe72cdf532853376ad4923-g20ccf816-vipendya
[*08/01/2034 00:14:49.5099] bootsh mini ramfs booted
[*08/01/2034 00:14:50.6744] cpio: etc/systemd/system/local-fs.target.wants/btldr_upgrade.service not created: newer or same age file exists
[*08/01/2034 00:14:58.1551] 288339 blocks
Welcome to Cisco.
- 添付品:写真をご確認ください。
1.配送方法、配送料金
ヤマト運輸、クリックポスト
送料無料(送料無料と設定されている商品)
落札者負担(落札者負担送料が設定されている商品)
2.商品発送について
ご入金確認後、3営業日以内にに発送させて頂きます。
3.返品・返送料金について
商品の初期不良(商品到着時点での破損、電源不良、動作不良等、スペックの相違 等)の場合、
保障期間内(商品到着後1週間以内)でご連絡いただくと、対応させて頂きます。
お客様の都合による返品の場合の返送料金はお客様負担となります。
4.返金について
取引完了後の初期不良、お客様の都合による返金に関しては販売手数料10%を引いた金額の返金となります。
取引完了前の初期不良、お客様の都合による場合は全額返金となります。
必ず初期不良の確認の上取引完了ボタンを押してください。
5.お問い合わせ
不明な点等ございましたら、質問欄または取引メッセージにてご相談ください。
営業日(土日祝日を抜く)10時~12時と13時~17時の間で対応させて頂きます。
6.領収書の発行
商品落札後にご連絡頂けましたら、商品に添付し発送させて頂きます。
ご希望の宛先などございましたら、取引メッセージにてご記載をお願い致します。
ダウンロード版で送り致します。
7.その他
商品落札後、のかんたん決済期限内にご入金お願い致します。